Intervening to freshen up the design and enhance the performance for 2019 of what is essentially BMW’s cash cow, and doing so well enough to keep up with the increasingly more potent competition from the likes of KTM and Ducati without throwing the baby out with the bathwater, was very definitely a major challenge for BMW’s R&D team headed by project leader Jochen Beck. So that’s surely one reason that the new-for-2019 R1250GS doesn’t look a whole lot different than the outgoing R1200GS that’s been in production since 2004, receiving three major updates along the way while building an ever more loyal band of customers for a bike whose versatility is legendary. The R1250GS has some big shoes to fill.

We will run through the basics on how to measure bearing clearances and illustrate how to avoid mistakes. This will also require some critical measuring tools. Let’s just put this right out front—measuring bearing clearances cannot be accomplished with Plastigauge. Those little pieces of wax thread are not precision measurement devices and should not be used to define bearing clearances. We know this may hurt some people’s feelings, but setting bearing clearances is a process that’s too important to allow anything short of your best effort.

Before we get into the actual process, it might be good to talk about generic clearances. The commonly accepted rule that most crankshaft manufacturers prefer for street and performance engines is 0.0010-inch for every 1-inch of journal diameter. So for a 2.45-inch small-block main journal, the bearing clearance would be 0.0024-inch. For a smaller 2.100-inch rod journal, the accepted clearance would be 0.0021-inch. Factory acceptable tolerances on a stock small-block Chevy are much wider than this.

Speaking to Knitting Trade Journal at the recent ITMA Asia + CITME exhibition, Company founder Mr. Irfan Yolcular said that the R&D centre was part of Nit Orme’s strategy of expanding its range of technical services and consultancy and services for knitting design and programming – all part of the company’s commitment to support its customers.

“People should know where their fish was caught, how and when, and what species it is. If you don’t know those things, you can’t make informed choices on whether you can eat a fish with a clear conscience,” says Callum Roberts of the University of York, UK, who wasn’t involved in the study.

For the customer, these improvements mean less lubricant stress, reduced friction and lower bearing temperatures, which in turn results in a more energy efficient bearing. Furthermore, the increase in performance capacity enables the bearing to be downsized for the application, with corresponding reductions in the weight of the bearing and its space requirements.

I am the editor-in-chief and co-founder of QuillandPad.com. Beyond that, I contribute my horological expertise to a variety of magazines, websites and publications all o…

the bearings in automotive yolks are usually needle roller, but assembly is the same indeed there are likely many YouTube videos of the process.

As a comparison, Earth’s axial tilt oscillates more mildly – between 22.1 and 24.5 degrees, going from one extreme to the other every 10,000 or so years.

Chapter 4. Sensor Bearing Market Industry Analysis 4.1. Porter’s 5 Force Model 4.1.1. Bargaining Power of Buyers 4.1.2. Bargaining Power of Suppliers 4.1.3. Threat of New Entrants 4.1.4. Threat of Substitutes 4.1.5. Competitive Rivalry 4.1.6. Futuristic Approach to Porter’s 5 Force Model 4.2. PEST Analysis 4.2.1. Political Scenario 4.2.2. Economic Scenario 4.2.3. Social Scenario 4.2.4. Technological Scenario 4.3. Value Chain Analysis 4.3.1. Supplier 4.3.2. Manufacturers/Service Provider 4.3.3. Distributors 4.3.4. Application 4.4. Key Buying Criteria 4.5. Regulatory Framework 4.6. Cost Structure Analysis 4.6.1. Raw Application Cost Analysis 4.6.2. Manufacturing Cost Analysis 4.6.3. Labour Cost Analysis 4.7. Investment Vs Adoption Scenario 4.8. Analyst Recommendation & Conclusion

For instance, you might think that washing off your raw turkey is a good way to clean it and avoid salmonella, but according to the USDA Food Safety and Inspection Service, this could actually cause more problems, as the "bacteria in raw meat and poultry juices can be spread to other foods, utensils, and surfaces" that way. Overall, the less you handle raw meat with your bare hands, the better, as per the CDC. The health agency recommends thoroughly washing your hands and all utensils you use to handle the raw meat as you’re getting ready to cook it.

The poem meticulously described the distinct ways he wanted to gratify this woman, only pausing to give room for the vocals of his accompanying performer.